www.bonsaiframework.com
Page tree

Versions Compared

Old Version 1

changes.mady.by.user Tin Pham

Saved on

compared with

New Version Current

changes.mady.by.user Tin Pham

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

With my iMac it is supported, but I need to also have a Mac router:

Code Block
Kitchen-iMac:~ tin.pham$ ifconfig -a
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
	options=3<RXCSUM,TXCSUM>
	inet6 ::1 prefixlen 128 
	inet 127.0.0.1 netmask 0xff000000 
	inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 
	nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	options=10b<RXCSUM,TXCSUM,VLAN_HWTAGGING,AV>
	ether 0c:4d:e9:a1:20:92 
	nd6 options=1<PERFORMNUD>
	media: autoselect (none)
	status: inactive
en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 88:63:df:90:06:6d 
	inet6 fe80::8a63:dfff:fe90:66d%en1 prefixlen 64 scopeid 0x5 
	inet 192.168.0.100 netmask 0xffffff00 broadcast 192.168.0.255
	nd6 options=1<PERFORMNUD>
	media: autoselect
	status: active
en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
	options=60<TSO4,TSO6>
	ether 32:00:15:cf:c0:00 
	media: autoselect <full-duplex>
	status: inactive
en3: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
	options=60<TSO4,TSO6>
	ether 32:00:15:cf:c0:01 
	media: autoselect <full-duplex>
	status: inactive
bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	options=63<RXCSUM,TXCSUM,TSO4,TSO6>
	ether 0e:4d:e9:1a:90:00 
	Configuration:
		id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
		maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
		root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
		ipfilter disabled flags 0x2
	member: en2 flags=3<LEARNING,DISCOVER>
	        ifmaxaddr 0 port 6 priority 0 path cost 0
	member: en3 flags=3<LEARNING,DISCOVER>
	        ifmaxaddr 0 port 7 priority 0 path cost 0
	nd6 options=1<PERFORMNUD>
	media: <unknown type>
	status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
	ether 0a:63:df:90:06:6d 
	media: autoselect
	status: inactive
awdl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1452
	ether ca:b1:af:a7:9c:f5 
	inet6 fe80::c8b1:afff:fea7:9cf5%awdl0 prefixlen 64 scopeid 0xa 
	nd6 options=1<PERFORMNUD>
	media: autoselect
	status: active
vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 00:50:56:c0:00:01 
	inet 192.168.19.1 netmask 0xffffff00 broadcast 192.168.19.255
vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ether 00:50:56:c0:00:08 
	inet 192.168.73.1 netmask 0xffffff00 broadcast 192.168.73.255

 

Example

Example of use,

Code Block
languagebash
sudo apt-get install wakeonlan # install
wakeonlan 88:63:DF:90:06:6D # wake my mac using my pre-recorded mac address
ping 192.168.0.100 # confirm it is up